AOR AR8200 Specifications Page 106
- Page / 142
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
106
(14) Configuration menu
The configuration (CONFIG) menu is used to set fundamental operating parameters and other variables
which do not appear in any other menu heading.
BEEP Confirmation & error tone
LAMP LCD & keypad illumination
CONTRAST LCD contrast adjustment
POWER-SAVE Delay & cycle power save
AUTO PWR-OFF Auto inactivity power off
REMOTE BPS RS232 baud rate
RMT-ID Computer control address
FREQ DISP Frequency readout on/off
WRITE PROT Global write protect
OPENING MESSAGE Change the power-up message
14-1 CONFIG BEEP
The AR8200 emits confirmation ‘beeps’ while the keypad and side
keys are used. A ‘HIGH’ pitched beep indicates correct operation
while a ‘LOW’ pitched beep indicates that an error or unexpected
entry has taken place. The volume of the beep is independent of
the main volume control and can be separately defined. It is
recommended that the beep facility be enabled, especially in the
early days while gaining familiarity of the receiver.
Beep is setup in the CONFIG menu. To access the config
menu . The first item in the
config menu is “BEEP”, the default is beep on with a volume level of 09. Use the main dial or ï ð
keys to vary beep level between the range of OFF and 01 to 09 with 09 being the loudest. The
key may be used as a short cut to 05.
to accept the data and return to a standard display. Alternatively
to abort entry or ò to move to the next item on the config menu (LAMP).
14-2 CONFIG LAMP
The AR8200 is equipped with high intensity green LEDs to illuminate the LCD and front panel keypad
when operating in areas of low level lighting.
While the AR8200 is switched on and connected to an external power source such as the charger
or d.c. lead, the lamp will be PERMANENTLY ON and
cannot be switched off
. The lamp will go out
when the AR8200 is switched off (when the batteries are being charged etc).
Section 14, 14-1, 14-2
- (1) AR8200 Index 1
- Section 1 1
- 1-1 Introduction 5
- 1-2 Take care of your radio 5
- Section 1-1, 1-2 5
- Section 1-2, 1-3 6
- 1-4 Accessories supplied 7
- Section 1-3, 1-4 7
- 1-5 Controls & functions 8
- Section 1-5 8
- 1-5-1 Keypad 9
- Section 1-5-1 9
- 1-5-2 Summary of keys 10
- Section 1-5-2 10
- 1-5-3 Side panel 15
- Section 1-5-3 15
- Section 1-6-1 17
- 1-6-2 Charging the NiCads 18
- 1-6-3 Cigar lighter lead 18
- Section 1-6-2, 1-6-3 18
- 1-6-4 Battery considerations 19
- Section 1-6-3, 1-6-4 19
- Section 2, 2-1 20
- 2-3 Fit the batteries 21
- Section 2-1, 2-2, 2-3 21
- 2-4-4 CLEAR key 23
- 2-4-5 MONITOR key 23
- 2-4-6 KEY LOCK 23
- Section 2-4-4, 2-4-5, 2-4-6 23
- Variable Frequency Oscillator 24
- Section 3-2 25
- Section 3-2, 3-3 26
- Section 3-3, 3-4, 3-5 27
- &Note: In AM and FM 28
- Section 3-5, 3-6 28
- 3-7 Changing receive mode 29
- 3-7-1 Auto-mode selection 29
- Section 3-7, 3-7-1, 3-7-2 29
- Section 3-7-2 30
- Section 3-7-2, 3-8 31
- Section 3-8 32
- 3-9 STEP-adjust 33
- Section 3-8, 3-9, 3-9-1 33
- 3-9-2 Cancelling step-adjust 34
- Section 3-9-1, 3-9-2, 3-93 34
- Section 3-93 35
- 3-10 FREQUENCY OFFSET 36
- Section 3-9-3, 3-10, 3-10-1 36
- Section 3-10-1, 3-10-2 37
- 3-11 Attenuator 38
- 3-12 Noise limiter 38
- Section 3-10-2, 3-11, 3-12 38
- Section 3-12, 3-13 39
- Section 3-13 40
- (4) VFO enhanced facilities 41
- 4-1 Quick memories 41
- Section 4, 4-1, 4-1-1 41
- VFO SEARCH 43
- Section 4-3-2, 4-3-3, 4-3-4 44
- Section 4-3-4, 4-3-5 45
- 4-3-6 Exiting VFO search 46
- 4-4 VFO environment menu 46
- 4-4-1 VFO SCAN 46
- 4-4-2 VFO search DELAY 46
- 5-1 Memory channel overview 51
- &Note: 51
- Section 5, 5-1 51
- Section 5-1, 5-2 52
- Section 5-2 53
- 5-4 Memory read “M.RD” 56
- Section 5-3, 5-4 56
- 5-5 Deleting memory channels 57
- Section 5-4-1, 5-5 57
- Section 6, 6-1, 6-2 60
- 7-2 SCAN considerations 62
- Section 7, 7-1, 7-2 62
- 7-3 Starting to SCAN 63
- Section 7-2, 7-3 63
- 7-4 Selecting a scan bank 64
- 7-5 Channel PASS 64
- Section 7-3, 7-3-1, 7-4, 7-5 64
- Section 7-5, 7-5-1, 7-5-2 65
- Section 7-7, 7-8 67
- 7-8-1 Scan DELAY 68
- 7-8-2 Scan LEVEL 68
- Section 7-8, 7-8-1, 7-8-2 68
- 7-9 Select scan 71
- Section 7-9-3, 7-9-4 72
- Section 7-9-4, 7-9-5 73
- (8) Search mode 74
- 8-1 Search types 74
- Section 8, 8-1, 8-1-1 74
- 8-3 Selection of search bank 76
- Section 8-2-4, 8-3 76
- Section 8-3 77
- 8-5-1 Search pass menu 80
- Section 8-5, 8-5-1 80
- Section 8-6, 8-7 82
- 8-7-1 Search DELAY 83
- Section 8-7, 8-7-1 83
- 8-7-7 Deleting search banks 87
- Section 8-7-7, 8-7-8 87
- (9) EDIT menu 88
- 9-1 EDIT COPY memory channel 88
- Section 9, 9-1 88
- (10) DELETE menu facilities 94
- Section 10, 10-1 94
- For example: 100
- (12) TEXT search and input 101
- 12-1 Text input menus 101
- Section 12, 12-1 101
- Section 12-2 102
- 12-2 Text search 102
- (13) SHORT CUT keys 103
- 13-1 Short cut menu access 103
- Section 13, 13-1 103
- 13-2 Short cut text entry 104
- Section 13-2 104
- Section 13-3 105
- (14) Configuration menu 106
- 14-1 CONFIG BEEP 106
- 14-2 CONFIG LAMP 106
- Section 14, 14-1, 14-2 106
- 14-4 CONFIG Power save 108
- Section 14-4 108
- 14-9 CONFIG Opening message 111
- Section 14-8, 14-9 111
- (15) Band scope 112
- 15-1 Starting the band scope 112
- Section 15, 15-1 112
- 15-8 Peak hold 114
- Section 15-10 115
- (16) Sleep ¹ 116
- Section 16 116
- (17) Option socket 117
- Section 17 117
- 17-1 RS232 operation 118
- Section 17-1, 17-2 118
- 17-2-1 How to clone data 119
- Section 17-2-1 119
- (18) Slot card socket 121
- 18-1 Optional slot cards 121
- 18-1-1 Fitting the slot card 121
- Section 18, 18-1, 18-1-1 121
- Section 18-1-1, 18-1-2, 18-2 122
- 18-3-1 CTCSS tone squelch 123
- Section 18-2, 18-3. 18-3-1 123
- 18-3-2 CTCSS search 124
- Section 18-3-1, 18-3-2 124
- «” will be displayed to 125
- Section 18-3-2, 18-4 125
- Section 18-4, 18-5, 18-5-1 126
- Section 18-6-1, 18-6-2 129
- Section 18-6-2, 18-6-3 130
- Section 18-6-4 131
- Section 18-6-7 134
- (19) Trouble shooting 136
- Section 19, 19-1, 19-2 136
- Section 19-2, 19-3 137
- (20) Optional accessories 138
- Section 20 138
- Section 21 139
- (22) Specification 140
- Section 22 140
- Fax: +81 3 3865 1697 141
- Downloaded by 142
- Amateur Radio Directory 142
Related products and manuals for Receiver AOR AR8200
Receiver AOR ARD9900 Instruction Manual
(36 pages)
(36 pages)
Receiver AOR AR2700 User Manual
(44 pages)
(44 pages)
Receiver AOR AR16 Instruction Manual
(108 pages)
(108 pages)
Receiver AOR AR8600 Service Manual
(8 pages)
(8 pages)
Receiver AOR AR8000 User Manual
(18 pages)
(18 pages)
Receiver AOR AR-Mini Specifications
(49 pages)
(49 pages)
Receiver AOR SR2200 User Manual
(2 pages)
(2 pages)
Receiver AOR AR7030 User Manual
(2 pages)
(2 pages)
Receiver AOR AR-ALPHA User Manual
(4 pages)
(4 pages)
Receiver AOR SDU-5000 Instruction Manual
(39 pages)
(39 pages)
Receiver AOR AR-3000A User Manual
(56 pages)
(56 pages)
Receiver AOR AR2300 User Manual
(4 pages)
(4 pages)
Receiver AOR AR7030 User Manual
(8 pages)
(8 pages)
Receiver AOR SDU-5000 User Manual
(43 pages)
(43 pages)
Receiver AOR ARD-25 User Manual
(24 pages)
(24 pages)
Receiver AOR AR2300 User Manual
(2 pages)
(2 pages)
Receiver AOR AR3030 User Manual
(32 pages)
(32 pages)
Receiver AOR AR7000 User Manual
(28 pages)
(28 pages)
Receiver AOR WX2000 Operations Instructions
(40 pages)
(40 pages)
Receiver AOR AR1000 User Manual
(7 pages)
(7 pages)
© 2020, manymanuals.com. All rights reserved. | 0.690 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals